Search

2014年5月18日 星期日

STM32F10X Nano v0.0.1

    最近比較有空上來更新一下blog,前陣子都在弄STM32的東西,所以為了方便畫了一個可以直接插上麵包板的實驗板,能相容STM32F100C8T6的IC應該都可以直接用,我用STM32F103C8T6也可以,當然load file不同而已,附上一個example測試PA0 weak up與PC13 led,我自己在使用都是用USART1去Upload程式,這個唯一的優點大概就是電路板可以用單面感光PCB做出來比較簡單,未來有時間會弄個jlink換SWD,然後再寫個GUI版的USART & SWD Upload程式。


Part List:

  • IC1:STM32F10X
  • U1:AMS-1117 3.3V
  • U2:8MHz Crystall
  • C1~C7:0.1uF
  • C8~C9:22pF
  • R1:1k ohm
  • R2~R3:10k ohm
  • L1~L2:電源與PC13 LED
  • B1~B2:Reset與PA0 weak up
  • JP1~JP3:GPIO與BOOT選擇



    JP3中間那支腳是B00T0,可與上下HIGH & LOW短路,JP1從最右邊數過來分別是5V、3.3V、GND,JP1最左邊是PA0一直到PB11,JP2最右邊開始則是PB12到PB9,都只有GPIO,PC13預留實驗用LED,PC14、15也預留可以焊音叉式Crystal。








Eaxmple:

#include "stm32f10x.h"
#include "stdio.h"

volatile uint32_t delay = 0;

void USART1_Send_Sting(char *string){
    while(*string){
        USART_SendData(USART1, (unsigned short int) *string++);

        while (USART_GetFlagStatus(USART1, USART_FLAG_TC) == RESET);
    }
}


void Init_WU()
{
  GPIO_InitTypeDef GPIO_InitStruct;

  RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA,ENABLE);

  GPIO_InitStruct.GPIO_Pin = GPIO_Pin_0;
  GPIO_InitStruct.GPIO_Mode = GPIO_Mode_IN_FLOATING;
  GPIO_Init(GPIOA, &GPIO_InitStruct);
}

void Init_UART(){
    GPIO_InitTypeDef GPIO_InitStructure;
    USART_InitTypeDef USART_InitStructure;
    NVIC_InitTypeDef interrup;

    RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA|RCC_APB2Periph_USART1, ENABLE);

    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;

    GPIO_Init(GPIOA, &GPIO_InitStructure);

    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;

    GPIO_Init(GPIOA, &GPIO_InitStructure);


    USART_InitStructure.USART_BaudRate = 9600;
    USART_InitStructure.USART_WordLength = USART_WordLength_8b;
    USART_InitStructure.USART_StopBits = USART_StopBits_1;
    USART_InitStructure.USART_Parity = USART_Parity_No;
    USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
    USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;

    USART_Init(USART1, &USART_InitStructure);

    USART_Cmd(USART1, ENABLE);

    USART_ITConfig(USART1,USART_IT_RXNE,ENABLE);

   interrup.NVIC_IRQChannel = USART1_IRQn;
   interrup.NVIC_IRQChannelPreemptionPriority = 0;
   interrup.NVIC_IRQChannelSubPriority = 0;
   interrup.NVIC_IRQChannelCmd = ENABLE;
   NVIC_Init(&interrup);

   NVIC_EnableIRQ(USART1_IRQn);
}

void Init_BT(void){
    GPIO_InitTypeDef GPIO_InitStructure;
    USART_InitTypeDef USART_InitStructure;
    NVIC_InitTypeDef interrup;

    RCC_APB1PeriphClockCmd(RCC_APB2Periph_GPIOA|RCC_APB1Periph_USART2, ENABLE);

    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_2;
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;

    GPIO_Init(GPIOA, &GPIO_InitStructure);

    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_3;
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;

    GPIO_Init(GPIOA, &GPIO_InitStructure);



    USART_InitStructure.USART_BaudRate = 9600;
    USART_InitStructure.USART_WordLength = USART_WordLength_8b;
    USART_InitStructure.USART_StopBits = USART_StopBits_1;
    USART_InitStructure.USART_Parity = USART_Parity_No;
    USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
    USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;

    USART_Init(USART2, &USART_InitStructure);

    USART_Cmd(USART2, ENABLE);

    USART_ITConfig(USART2,USART_IT_RXNE,ENABLE);

   interrup.NVIC_IRQChannel = USART2_IRQn;
   interrup.NVIC_IRQChannelPreemptionPriority = 0;
   interrup.NVIC_IRQChannelSubPriority = 0;
   interrup.NVIC_IRQChannelCmd = ENABLE;
   NVIC_Init(&interrup);

   NVIC_EnableIRQ(USART2_IRQn);
}

void BT_Send_String(volatile char *string)
{
   while(*string){
      USART_SendData(USART2,*string);
      ++string;
      while(USART_GetFlagStatus(USART2,USART_FLAG_TC) == RESET){}
   }
}

void PWR_StandbyMode( void )
{
  RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR | RCC_APB1Periph_BKP, ENABLE);

  PWR_WakeUpPinCmd(ENABLE);
  PWR_BackupAccessCmd(ENABLE);
  PWR_ClearFlag(PWR_FLAG_SB);
  PWR_EnterSTANDBYMode();
}

void Init_Default_Led(void)
{
   GPIO_InitTypeDef led;

   RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC,ENABLE);


   led.GPIO_Pin = GPIO_Pin_13;
   led.GPIO_Mode = GPIO_Mode_Out_PP;
   led.GPIO_Speed = GPIO_Speed_50MHz;

   GPIO_Init(GPIOC,&led);

}

void Delay(volatile uint32_t n)
{
   delay = n;
   while(delay != 0);
}


int main(){
    Init_UART();
    Init_BT();
    Init_Default_Led();
    Init_WU();

    SystemInit();
    if(SysTick_Config(SystemCoreClock / 1000)){
       while(1);
    }

    char str[256];
    sprintf(str,"\n\nFlash Size : %dKb\nUID : %X%X%X\n",*(volatile u16*)(0x1FFFF7E0),
 *(volatile u32*)(0x1FFFF7E8),*(volatile u32*)(0x1FFFF7EC),*(volatile u32*)(0x1FFFF7F0));
    USART1_Send_Sting(str);
    BT_Send_String(str);

    while(1){
       GPIO_SetBits(GPIOC,GPIO_Pin_13);
       Delay(1000);
       GPIO_ResetBits(GPIOC,GPIO_Pin_13);

       PWR_StandbyMode();
    }
}

void USART1_IRQHandler(void)
{
   if(USART_GetITStatus(USART1,USART_IT_RXNE) != RESET){

      char c = USART1->DR/*USART_ReciveData(USART1)*/;

      USART_SendData(USART1,c);
   }
}

void USART2_IRQHandler(void)
{
   if(USART_GetITStatus(USART2,USART_IT_RXNE) != RESET){

      char c = USART2->DR/*USART_ReciveData(USART2)*/;

      USART_SendData(USART2,c);
   }
}

void SysTick_Handler(void)
{
   if(delay != 0){
      delay--;
   }
}











沒有留言:

張貼留言